国产三线在线,亚洲久草在线视频,9久re热视频在线精品,久久久xxx

Baldor運動控制器  NextMove ESB-2
Baldor運動控制器 NextMove ESB-2
產品價格:¥面議(人民幣)
  • 規格:NextMove ESB-2
  • 發貨地:英國
  • 品牌:
  • 最小起訂量:1件
  • 免費會員
    會員級別:試用會員
    認證類型:未認證
    企業證件:未通過
    認證信息:未認證

    商鋪名稱:蘇州奧特維新自動控制設備有限公司

    聯系人:袁先生(先生)

    聯系手機:

    固定電話:

    企業郵箱:autmotion@163.com

    聯系地址:蘇州市金閶區新元路5號

    郵編:215003

    聯系我時,請說是在線纜網上看到的,謝謝!

    商品詳情

      我司是Baldor控制器中國地區唯一授權經銷商

      NextMove ESB-2的詳細描述:

      軸數:可選3個或4個閉環軸另加4個開環軸。

      軸的類型:閉環伺服/矢量:帶有速度和加速度正向輸送項的PID。每100微妙更新一次。開環:步進/方向 峰值頻率500kHZ。差分或可選用的5V開集電極。

      位置反饋信號 伺服/矢量 增量式編碼器 RS422 帶有索引(Z)脈沖的差分A、B信號,峰值頻率20MHZ。

      輔助編碼器 2個帶3軸閉環變量 1個帶4軸閉環變量,可以用于位置跟蹤,位置校驗或者雙編碼器反饋。

      板載內存 用于固件和程序存儲的2Mb字節的內存。2Mb字節的做靜態存儲器。用作參數存儲的32Kb字節的非易失性RAM器。

      數字輸入 20光隔離24伏直流輸入。采樣率為1ms。可接到通用正負極(與NPN或PNP輸出晶體管配套使用),可為范圍(正反向)、復位、停機和驅動器誤差配置的軟件。

      數字輸出 12個光電分離的12-24VDC PNP 用于啟動驅動器的可配置軟件 每信道標準為50mA 單信道最大負載為350mA 8個信道合計500mA

      模擬輸出 輸出3或4次驅動控制信號 對于驅動命令信號,有三種輸出功率 ±10V、12位分辨率 一通用±10V12位輸出

      模擬輸入 2個微分輸入 兩種誤差不超過V±10V,12位分辨率下運行

      繼電器輸出 單輸出適用于驅動器啟用,額定值為24V(150mA)的C型繼電器(單刀雙鄭),一般為常開常閉狀態

      串行口 RS485/232

      Can總線端口 標準的9針Sub-D型連接器的單CAN端口等

      其它資料請聯系咨詢

      本公司供應Baldor NextMove ESB-2可編程控制器質量保證,歡迎咨詢洽談。

      NextMove ESB-2Panel mount 8 axis motion controllerNextMove ESB-2 a compact panel mount motion controller for the control of up to 8 axes - 4 servo, 4 open loop stepper. NextMove ESB-2, coupled with MINT motion programming, offers a high speed and flexible motion controller. On board I/O can be used to control many parts of the machine. This can be further expanded with either ABB's range of CAN I/O modules operating over the CAN bus, or alternatively, CANopen devices conforming to the standard DS401 I/O profile.

      Versatile programming is provided by means of MINT - multitasking BASIC, or the supplied ActiveX components for PC based interfaces and is compatible with our MintNC 2.5 axis CAD to motion solution.

      For motion control with Ethernet connectivity see NextMove e100

      Features:
    • Panel mount configuration with two-part connectors and D-type connector for encoder connections
    • 1MByte SRAM for user programs and data
    • 1MByte FLASH for firmware and user program storage
    • 32kByte FRAM for non-volatile parameter storage
    • Product variants available for 3 or 4 axes of servo control and 4 axes of stepper control MicroFlex can be used in step and direction mode for additional 'open loop' servo axes)
    • 20 PNP/NPN opto-isolated digital inputs
      Programmable for hardware limits, home input, stop input and error input. 4 of the inputs can be programmed for high speed capture of position with 1 microsecond
    • 12 PNP opto-isolated digital outputs
    • 24V/150mA relay output to signal system error conditions
    • 2 x 12-bit analog inputs
    • 12-bit analog output for 3 axis variant
    • Two auxiliary encoder interfaces for position following or position verification with 3-axis servo variant. One additional auxiliary encoder interface for 4-axis servo variant
    • USB programming interface
    • RS232 (115,200 Baud) and (optional RS485)
    • CAN interface for I/O expansion and HMI interfaces. Can be used to provide full peer-to-peer networking capabilities with other MINT based controllers
    • Multi-tasking programming capability with MINT-MT. Number of tasks limited only by available memory
    • Comprehensive move types including: linear, circular and helical interpolation; software cams; flying shears; splines; synchronization with positional offsets and virtual axes
    • ActiveX libraries supplied free of charge
    • Compatible with MINT NC and HPGL
    • RoHS compliant Ordering information and accessories: Catalog numberDescription
      NSB202-501W NextMove ESB motion controller. 3 axes servo, 4 axes stepper. RS232 and USB serial interfaces
      NSB202-502W
      NextMove ESB motion controller. 3 axes servo, 4 axes stepper. RS485 and USB serial interfaces
      NSB203-501W NextMove ESB motion controller. 3 axes servo, 4 axes stepper. RS232 and USB serial interfaces. For use with ABB DSMS Stepper Motors
      NSB203-502W
      NextMove ESB motion controller. 3 axes servo, 4 axes stepper. RS485 and USB serial interfaces. For use with ABB DSMS Stepper Motors
      NSB204-501W NextMove ESB motion controller. 4 axes servo, 4 axes stepper. RS232 and USB serial interfaces
      NSB204-502W
      NextMove ESB motion controller. 4 axes servo, 4 axes stepper. RS485 and USB serial interfaces
      NSB205-501W NextMove ESB motion controller. 4 axes servo, 4 axes stepper. RS232 and USB serial interfaces. For use with ABB DSMS Stepper Motors
      NSB205-502W
      NextMove ESB motion controller. 4 axes servo, 4 axes stepper. RS485 and USB serial interfaces. For use with ABB DSMS Stepper Motors
      CBL001-501
      2m (6ft) RS232 cable for programming and diagnostics
      (note: 2m (6ft) USB cable included with NSB002-501)
      MNC001-501 MINTNC - profiling front end for NextMove which accepts industry standard files: HPGL, DXF and G-code.
    在線詢盤/留言
  • 0571-87774297  
    主站蜘蛛池模板: 清远市| 东宁县| 化州市| 鸡东县| 滁州市| 漳浦县| 唐山市| 雅安市| 玉田县| 达拉特旗| 武宁县| 浑源县| 平度市| 衡阳市| 巴林右旗| 钦州市| 芒康县| 宜阳县| 罗田县| 镇巴县| 大城县| 双桥区| 蓝田县| 化州市| 沂南县| 望江县| 唐河县| 崇明县| 邵阳县| 三门县| 双鸭山市| 垦利县| 宝坻区| 佛学| 鄂州市| 内丘县| 广东省| 公安县| 常德市| 霍山县| 广东省|